<<Actor>> Maintenance {Analysis} derived from: Operator, User

Documentation
Specific role of a User.
Maintenance has more priviledge than any other user of the system.

Associations

Name	My Role	My Class	Other Role	Other Element
Configure AT to Station
Get AT Observing Station
Configure AT to Relocation
Ignore Sub-System
ATCS Global System State Update
--Not Named--	--Not Defined--
AO/ACT access control
ATCS Start
ATCS Stop
ATCS Shutdown
ATCS Cold Start
AT System Start
AT System Stop
CFD
Set Coude Beam Switching Device
ACS
Get Enclosure Temperature
Get Dew Point Temperature
Stop Air Conditioning
Start Air Conditioning
Check Status Air Conditioning
Set Reference Temperature
Set Dew Point Margin
ROS
Control ROS
Get ROS Status
ECS
Read Enclosure Anemometers
Open Enclosure
Close Enclosure
Check Status Enclosure
TRL
Check Status Anchors
PRS
Stop Telescope Motion
Preset Telescope to Named Position
Preset Telescope to Named Position
Preset Telescope to Astronomical Coordinates
Preset Telescope in Alt/Az Coordinates
Stop Telescope Motion
Preset Telescope to Named Position
Preset Telescope in Alt/Az Coordinates
Preset Telescope to Astronomical Coordinates
Stop FAS Acquisition
Stop FAS Acquisition
Save Guide Detector Image
Set FAS Integration Time
Set Guide Window Size
Display Guide Detector Signals
Prepare FAS Setup
Start FAS Acquisition
PRS
OPT
ATCS
AG
FS
CHP
TRK
Read Telescope Temperature Sensors
Set M2 Focus Position
Set M2 Center Position
Set M2 Tilt Angles
Switch On/Off Pupil Beacon Light Source
Center M10
Stop FAS Acquisition
Start Autoguiding
Stop Autoguiding
Get Tracking Remaining Time
Set Tracking Wavelength
Telescope Offset
Center Guide Star
Prepare for Image Alignment
Adjust Coude Focus
Prepare for VLTI Focus Adjustment
Prepare for Pupil Alignment
Set Tracking Additional Velocity
Stop Telescope Motion
Preset Telescope to Catalogue Object
Combined Offset
Center M6
Set M6 Tilt Angles
Set FSS Filter Wheel
Offset Alt/Az
Start Chopping
Stop Chopping
Configure Chopping
Set Remaining Tracking Time Limit
Select Instrument
Set Instrument Data
Get Instrument Data
Measure and Install POM
Modify POM term
Set Storage Mode for Pointing Measurements
Store POM Measure
Make POM
Install POM
Make Pointing Error Measurement
Get M2 Focus Position
Set Guide Parameters
Switch On/Off Nasmyth Beacon Light Source
Set Nasmyth Wheel
Get Guide Star Data
Center Object
Probe to Next Guide Star
Set Guide Reference Point
Get M2 Tilt Angles
Get M6 Tilt Angles
Get M10 Tilt Angles
Get AT Observing Station
Prepare FSS Setup
Start FSS Acquisition
Stop FSS Acquisition
Set FSS Field Diaphragm
Combined Offset
Set M10 Tilt Angles
ATCS Global System State Update
Center Object
Stop Field Stabilization
Start Field Stabilization
Get M2 Center Position
Control HPS
Ignore Sub-System
Configure AT to Relocation
Configure AT to Station
Get AT Observing Station
Stop Image Alignment
Stop Pupil Alignment
Prepare for Delay Constant Alignment
Stop Delay Constant Alignment
Stop VLTI Focus Adjustment
Calibrate M6 versus Coude Sensors
Calibrate Az axis
Check STRAP Pupil Alignment
Offset Guide Probe on Beacon
Guide Probe to Beacon
Offset Guide Probe on star
Optimize Field Stabilisation
Get FSS Filter Wheel
Get FSS Field Diaphragm
Set M2 Pupil Beacon Light Level
Control FS Corrections
Set Nasmyth Beacon Light Level
Do one calibrated correction
Start cyclic calibrated corrections
Cyclic closed loop active optics corrections
Do one star analysis
Stop current action
Adjust Pointing Axis Reference Points
POM
TRK
Stop Tracking
Install New PCM
TRK LCU
Coordinate Conversion
trk Workstation
FSS
Preset FSS Translation Stage
Get Local Seeing
Get FS Coherence Time
Start Strap Chopping
Stop Strap Chopping
Setup Strap Chopping
Disable FS
Enable FS
OPT
Prepare for Image Alignment
Prepare for Pupil Alignment
Adjust Coude Focus
Prepare for VLTI Focus Adjustment
Stop Image Alignment
Stop Image Alignment
Prepare for Pupil Alignment
Prepare for Image Alignment
Stop VLTI Focus Adjustment
Stop VLTI Focus Adjustment
Prepare for VLTI Focus Adjustment
Stop Pupil Alignment
Stop Pupil Alignment
Prepare for Delay Constant Alignment
Prepare for Delay Constant Alignment
Stop Delay Constant Alignment
Stop Delay Constant Alignment
Offset Guide Probe on Beacon
Calibrate Az axis
Calibrate Az axis
Calibrate M6 versus Coude Sensors
Calibrate M6 versus Coude Sensors
Guide Probe to Beacon
Check STRAP Pupil Alignment
Check STRAP Pupil Alignment
Calibrate M6 versus Coude Sensors
NFD
M6 Device
Get M6 Tilt Angles
Set M6 Tilt Angles
Center M6
Enable FS Corrections
Disable FS Corrections
M2 Device
Set M2 Pupil Beacon Light Level
Center M10
Set M10 Tilt Angles
Get M10 Tilt Angles
M10 Device
CHP
Enable Field Stabilisation
Disable FIeld Stabilisation
AG
Start Autoguiding
Stop Autoguiding
Stop Autoguiding
Start Autoguiding
Stop Autoguiding
AG
AG
vltguiag
AG WS
agwsControl
Services
Switch On/Off STRAP Hw Gate
Power On/Off FAS
Power On/Off M6
Reset STRAP VME board
Standard Command
GUI
Optical Alignment Gui
Pointing Model Gui
Select Guide Star
Chopping Gui
FAS Gui
FSS Gui
FS Gui
ATCS Control Gui
ATCS Status Gui
AG Gui
Set FAS Reference Point
Control differential tracking
Set additional velocity for probe
Check if guide probe is in position
Check if given coordinates result in a valid position
Move probe to science object
Offset probe in alpha/delta
Center the probe
Park the probe
Move probe to alternate position
Get Remaining tracking time
Update parameters from database
FS
Start Field Stabilization
Stop Field Stabilization
Stop Field Stabilization
TIF
Route Command
TIF
TIF
ACT
Cyclic closed loop active optics corrections
Do one calibrated correction
Start cyclic calibrated corrections
Do one star analysis
Stop current action
Stop current action
Start cyclic calibrated corrections
Do one correction
TSD
Set FSS Translation Stage
Set FSS Translation Stage
Set FSS Translation Stage
Set FSS Translation Stage
TCSMON

Generalization Relationships

Name	Class	Supplier
--Not Named--	Maintenance	Operator
--Not Named--	Maintenance	User
--Not Named--	Operator	Observer
--Not Named--	Operator	User
--Not Named--	Observer	User